Server : Apache
System : Linux server1.cgrithy.com 3.10.0-1160.95.1.el7.x86_64 #1 SMP Mon Jul 24 13:59:37 UTC 2023 x86_64
User : nobody ( 99)
PHP Version : 8.1.23
Disable Function : NONE
Directory : /usr/share/mibs/ietf/
|
Server : Apache System : Linux server1.cgrithy.com 3.10.0-1160.95.1.el7.x86_64 #1 SMP Mon Jul 24 13:59:37 UTC 2023 x86_64 User : nobody ( 99) PHP Version : 8.1.23 Disable Function : NONE Directory : /usr/share/mibs/ietf/ |
DOCS-CABLE-DEVICE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
IpAddress,
Unsigned32,
Counter32,
Integer32,
zeroDotZero,
mib-2
FROM SNMPv2-SMI -- RFC 2578
RowStatus,
RowPointer,
DateAndTime,
TruthValue,
StorageType
FROM SNMPv2-TC -- RFC 2579
InetAddressType,
InetAddress
FROM INET-ADDRESS-MIB -- RFC 4001
OBJECT-GROUP,
MODULE-COMPLIANCE
FROM SNMPv2-CONF -- RFC 2580
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB -- RFC 3411
InterfaceIndexOrZero
FROM IF-MIB -- RFC 2863
ZeroBasedCounter32
FROM RMON2-MIB -- RFC 4502
diffServMIBDataPathGroup,
diffServMIBClfrGroup,
diffServMIBClfrElementGroup,
diffServMIBMultiFieldClfrGroup,
diffServMIBActionGroup,
diffServMIBDscpMarkActGroup,
diffServMIBCounterGroup,
diffServMIBAlgDropGroup,
diffServDataPathStatus,
diffServClfrStatus,
diffServClfrElementStatus,
diffServMultiFieldClfrAddrType,
diffServMultiFieldClfrSrcAddr,
diffServMultiFieldClfrDstAddr,
diffServAlgDropStatus,
diffServDataPathStorage,
diffServClfrStorage,
diffServClfrElementStorage,
diffServMultiFieldClfrStorage,
diffServActionStorage,
diffServCountActStorage,
diffServAlgDropStorage,
diffServAlgDropType
FROM DIFFSERV-MIB; -- RFC 3289
docsDev MODULE-IDENTITY
LAST-UPDATED "200612200000Z" -- December 20, 2006
ORGANIZATION "IETF IP over Cable Data Network
Working Group"
CONTACT-INFO
" Rich Woundy
Postal: Comcast Cable
27 Industrial Avenue
Chelmsford, MA 01824 U.S.A.
Phone: +1 978 244 4010
E-mail: richard_woundy@cable.comcast.com
Kevin Marez
Postal: Motorola Corporation
6450 Sequence Drive
San Diego, CA 92121 U.S.A.
Phone: +1 858 404 3785
E-mail: kevin.marez@motorola.com
IETF IPCDN Working Group
General Discussion: ipcdn@ietf.org
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy,
richard_woundy@cable.comcast.com
Jean-Francois Mule,
jf.mule@cablelabs.com"
DESCRIPTION
"This is the MIB Module for DOCSIS-compliant cable modems
and cable-modem termination systems.
Copyright (C) The IETF Trust (2006). This version
of this MIB module was published in RFC 4639; for full
legal notices see the RFC itself."
REVISION "200612200000Z" -- December 20, 2006
DESCRIPTION
"Second version, published as RFC 4639.
Modifications to this MIB module since RFC 2669 include:
- Deprecation of the docsDevFilter group in favor of the
DiffServ MIB groups, to enable support for IPv6
filtering and DiffServ Code Point (DSCP) marking.
- Deprecation of the docsDevCpeGroup in favor of the
docsDevCpeInetGroup, to enable support of IPv6.
- Addition of various InetAddress objects to enable
support of IPv6.
- Deprecation of docsDevNmAccessTable in favor of SNMP
Coexistence and SNMPv3 -- yet adding
docsDevNmAccessTrapVersion and clarifying
docsDevNmAccessIp for current use of this table,
- Addition of docsDevIgmpModeControl for management and
control of the IGMP mode of operation,
- Addition of docsDevMaxCpe for management of the
maxmium number of CPEs permitted access through a
cable modem,
- Addition of docsDevSwServerTransportProtocol, and
modifications to docsDevSoftware object DESCRIPTIONS,
to enable software downloads via either TFTP or HTTP,
- Replacement of docsDevEvThrottleInhibited with
docsDevEvThrottleThresholdExceeded to simplify
event threshold management,
- Modification of docsDevEvReporting to enable local
logging to the internal volatile log, and not to the
internal non-volatile log,
- Modification of the compliance statement to make the
docsDevCpe objects optional
- Created placeholders for two OIDs in the
docsDevFilterPolicyTable that were never used
- Modified the DESCRIPTION of
docsDevSwServerTransportProtocol and
docsDevSwServerAddressType to address the
dependence between each object
- Added a reference to docsDevServerConfigTftpAddress
- Clarified the scope of notifications that are covered
by docsDevEvThrottleThreshold
- Clarified an error condition that could occur when
doing a SET to docsDevEvReporting
- Defined each of the enumerated types for both
docsDevEvLevel and docsDevEvPriority
- Added UNITS clause to docsDevFilterLLCMatches,
docsDevFilterIpMatches, docsDevMaxCpe,
docsDevEvThrottleThreshold and docsDevEvCounts.
- Added REFERENCE clause to docsDevFilterIpProtocol
- Modified DESCRIPTION of docsDevCpeInetAddr to be
more protocol-neutral
- Removed the enumerated value (1) from both
docsDevCpeInetSource and docsDevCpeSource
- Covered additional read-write and read-create objects
in the Security Considerations section
- Modified the default value of docsDevNmAccessIpMask
to be consistent with OSSI specification
- Modified the SYNTAX of docsDevNmAccessCommunity and
docsDevNmAccessInterfaces in the Conformance
Statement section
- Added SYNTAX clause to docsDevEvReporting in the
Conformance Statement section
- Modified SYNTAX clause of docsDevEvReporting to
move new enumerated type to byte boundary
- Added references to DOCSIS 2.0 specifications to
multiple objects
- Clarified non-persistency across reboots for
all tables
- Clarified functionality of docsDevSw objects as
they relate to docsDevSwOperStatus
- Clarified enumerated types (9) and (10) for
docsDevServerBootState
- Defined the state of unknown(0) for the following
objects: docsDevServerDhcpAddressType,
docsDevServerTimeAddressType,
docsDevServerConfigTftpAddressType and
docsDevServerConfigTftpAddressType
- Modified the value in docsDevFilterIpDaddr to be
consistent with the SYNTAX
- Specified which rows could be modified in an
active row for docsDevFilterPolicyStatus
- Defined the term 'manually' in docsDevCpeEnroll
- Clarified the description for
docsDevFilterTosOrMask
- Covered the case of a non-existent row for
docsDevFilterPolicyPtr
- Added DEFVAL clauses for multiple objects
- Replaced docsDevNotification OBJECT IDENTIFIER
with docsDevNotifications to address possible
compatibility issues
- Added support for the usage of RFC 3413 and RFC 3014
as event notification mechanisms
- Removed docsDevFilterPolicyObsoleteGroup
- Added stdInterface(9) type to docsDevEvReporting to
support the usage of RFC3413 and RFC3014
- Modified DESCRIPTION for docsDevMaxCpe"
REVISION "199908190000Z"
DESCRIPTION
"Initial version, published as RFC 2669."
::= { mib-2 69 }
docsDevMIBObjects OBJECT IDENTIFIER ::= { docsDev 1 }
docsDevBase OBJECT IDENTIFIER ::= { docsDevMIBObjects 1 }
--
-- For the following object, there is no concept in the
-- RFI specification corresponding to a backup CMTS. The
-- enumeration is provided here in case someone is able
-- to define such a role or device.
--
docsDevRole OBJECT-TYPE
SYNTAX INTEGER {
cm(1),
cmtsActive(2),
cmtsBackup(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines the current role of this device. cm(1) is a
Cable Modem, cmtsActive(2) is a Cable Modem Termination
System that is controlling the system of cable modems,
and cmtsBackup(3) is a CMTS that is currently connected
but is not controlling the system (not currently used).
In general, if this device is a 'cm', its role will not
change during operation or between reboots. If the
device is a 'cmts' it may change between cmtsActive and
cmtsBackup and back again during normal operation. NB:
At this time, the DOCSIS standards do not support the
concept of a backup CMTS, but cmtsBackup is included for
completeness."
::= { docsDevBase 1 }
docsDevDateTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The current date and time, with time zone information
(if known).
If the real data and time cannot be determined, this
shall represent elapsed time from boot relative to
the standard epoch '1970-1-1,0:0:0.0'. In other
words, if this agent has been up for 3 minutes and
not been able to determine what the actual date and
time are, this object will return the value
'1970-1-1,0:03:0.0'."
::= { docsDevBase 2 }
docsDevResetNow OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to true(1) causes the device to
reset. Reading this object always returns false(2)."
::= { docsDevBase 3 }
docsDevSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The manufacturer's serial number for this device."
::= { docsDevBase 4 }
docsDevSTPControl OBJECT-TYPE
SYNTAX INTEGER {
stEnabled(1),
noStFilterBpdu(2),
noStPassBpdu(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls operation of the spanning tree
protocol (as distinguished from transparent bridging).
If set to stEnabled(1), then the spanning tree protocol
is enabled, subject to bridging constraints.
If noStFilterBpdu(2), then spanning tree is not active,
and Bridge PDUs received are discarded.
If noStPassBpdu(3), then spanning tree is not active,
and Bridge PDUs are transparently forwarded.
Note that a device need not implement all of these
options, but that noStFilterBpdu(2) is required."
DEFVAL { noStFilterBpdu }
::= { docsDevBase 5 }
docsDevIgmpModeControl OBJECT-TYPE
SYNTAX INTEGER {
passive(1),
active(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the IGMP mode of operation for
the CM or CMTS. In passive mode, the device forwards
IGMP between interfaces as based on knowledge of
Multicast Session activity on the subscriber side
interface and the rules defined in the DOCSIS RFI
specification. In active mode, the device terminates
at and initiates IGMP through its interfaces as based
on the knowledge of Multicast Session activity on the
subscriber side interface."
REFERENCE
"DOCSIS RFI 1.1 Specification, Section 3.3.1. and
DOCSIS RFI 2.0 Specification, Section 5.3.1."
DEFVAL { passive }
::= { docsDevBase 6 }
docsDevMaxCpe OBJECT-TYPE
SYNTAX Unsigned32 (0..255)
UNITS "CPEs"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of CPEs that can be granted access
through a CM during a CM epoch. This value can be
obtained from the CM configuration file; however,
it may be adjusted by the CM according to hardware or
software limitations that have been imposed on the
implementation."
REFERENCE
"DOCSIS RFI 1.0 Specification, Appendix C.7.20., and
DOCSIS RFI 1.1 Specification, Appendix C.1.1.7. and
DOCSIS RFI 2.0 Specification, Appendix C.1.1.7."
::= { docsDevBase 7 }
--
-- The following table provides one level of security for access
-- to the device by network management stations.
-- Note that access is also constrained by the
-- community strings and any vendor-specific security.
--
docsDevNmAccessTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevNmAccessEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table controls access to SNMP objects by network
management stations. If the table is empty, access to
SNMP objects is unrestricted. The objects in this table
MUST NOT persist across reboots. The objects in this
table are only accessible from cable devices that are
not capable of operating in SNMP Coexistence mode
(RFC 3584) or in SNMPv3 mode (RFC 3410).
See the conformance section for
details. Note that some devices are required by other
specifications (e.g., the DOCSIS OSSIv1.1 specification)
to support the legacy SNMPv1/v2c docsDevNmAccess mode
for backward compatibility.
This table is deprecated. Instead, use the SNMP
coexistence MIBs from RFC 3584, the TARGET and
NOTIFICATION MIBs from RFC 3413, and
the View-Based Access Control Model (VACM) MIBs for
all SNMP protocol versions from RFC 3415."
::= { docsDevMIBObjects 2 }
docsDevNmAccessEntry OBJECT-TYPE
SYNTAX DocsDevNmAccessEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry describing access to SNMP objects by a
particular network management station. An entry in
this table is not readable unless the management station
has read-write permission (either implicit if the table
is empty, or explicit through an entry in this table).
Entries are ordered by docsDevNmAccessIndex. The first
matching entry (e.g., matching IP address and community
string) is used to derive access."
INDEX { docsDevNmAccessIndex }
::= { docsDevNmAccessTable 1 }
DocsDevNmAccessEntry ::= SEQUENCE {
docsDevNmAccessIndex Integer32,
docsDevNmAccessIp IpAddress,
docsDevNmAccessIpMask IpAddress,
docsDevNmAccessCommunity OCTET STRING,
docsDevNmAccessControl INTEGER,
docsDevNmAccessInterfaces OCTET STRING,
docsDevNmAccessStatus RowStatus,
docsDevNmAccessTrapVersion INTEGER
}
docsDevNmAccessIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Index used to order the application of access
entries."
::= { docsDevNmAccessEntry 1 }
docsDevNmAccessIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The IP address (or subnet) of the network management
station. The address 0.0.0.0 is defined to mean
any Network Management Station (NMS). If traps are
enabled for this entry, then the value must be the
address of a specific device. Implementations MAY
recognize 255.255.255.255 as equivalent to 0.0.0.0."
DEFVAL { '00000000'h }
::= { docsDevNmAccessEntry 2 }
docsDevNmAccessIpMask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The IP subnet mask of the network management stations.
If traps are enabled for this entry, then the value must
be 0.0.0.0. Implementations MAY recognize
255.255.255.255 as equivalent to 0.0.0.0."
DEFVAL { '00000000'h }
::= { docsDevNmAccessEntry 3 }
docsDevNmAccessCommunity OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The community string to be matched for access by this
entry. If set to a zero-length string, then any
community string will match. When read, this object
SHOULD return a zero-length string."
DEFVAL { "public" }
::= { docsDevNmAccessEntry 4 }
docsDevNmAccessControl OBJECT-TYPE
SYNTAX INTEGER {
none(1),
read(2),
readWrite(3),
roWithTraps(4),
rwWithTraps(5),
trapsOnly(6)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Specifies the type of access allowed to this NMS.
Setting this object to none(1) causes the table entry
to be destroyed. Read(2) allows access by 'get' and
'get-next' PDUs. ReadWrite(3) allows access by 'set' as
well. RoWithtraps(4), rwWithTraps(5), and trapsOnly(6)
control distribution of Trap PDUs transmitted by this
device."
DEFVAL { read }
::= { docsDevNmAccessEntry 5 }
-- The syntax of the following object was copied from RFC 1493,
-- dot1dStaticAllowedToGoTo.
docsDevNmAccessInterfaces OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..32))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Specifies the set of interfaces from which requests from
this NMS will be accepted. Each octet within
the value of this object specifies a set of eight
interfaces, the first octet specifying ports 1
through 8, the second octet specifying interfaces 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
interface, and the least significant bit represents the
highest numbered interface. Thus, each interface is
represented by a single bit within the value of this
object. If that bit has a value of '1' then that
interface is included in the set.
Note that entries in this table apply only to link-layer
interfaces (e.g., Ethernet and CATV MAC). Bits
representing upstream and downstream channel interfaces
MUST NOT be set to '1'.
Note that if bits corresponding to non-existing
interfaces are set, the result is implementation
specific.
Note that according to the DOCSIS OSSIv1.1
specification, when ifIndex '1' is included in the
set, then this row applies to all CPE
(customer-facing) interfaces.
The size of this object is the minimum required to
represent all configured interfaces for this device."
::= { docsDevNmAccessEntry 6 }
docsDevNmAccessStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Controls and reflects the status of rows in this
table. Rows in this table may be created by either the
create-and-go or create-and-wait paradigm. There is no
restriction on changing values in a row of this table
while the row is active.
The following objects MUST have valid values before this
object can be set to active: docsDevNmAccessIp,
docsDevNmAccessStatus, docsDevNmAccessIpMask,
docsDevNmAccessCommunity, docsDevNmAccessControl, and
docsDevNmAccessInterfaces."
::= { docsDevNmAccessEntry 7 }
docsDevNmAccessTrapVersion OBJECT-TYPE
SYNTAX INTEGER {
disableSNMPv2trap(1),
enableSNMPv2trap(2)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Specifies the TRAP version that is sent to this NMS.
Setting this object to disableSNMPv2trap (1) causes the
trap in SNMPv1 format to be sent to a particular NMS.
Setting this object to enableSNMPv2trap (2) causes the
trap in SNMPv2 format be sent to a particular NMS."
DEFVAL { disableSNMPv2trap }
::= { docsDevNmAccessEntry 8 }
--
-- The following group describes control objects used for downloading
-- firmware to a cable device. Procedures for software download are
-- described in Section 3.2.1 of the RFC containing this MIB module.
--
docsDevSoftware OBJECT IDENTIFIER ::= { docsDevMIBObjects 3 }
docsDevSwServer OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The address of the TFTP server used for software
upgrades. If the TFTP server is unknown or is a
non-IPv4 address, return 0.0.0.0.
This object is deprecated. See docsDevSwServerAddress
for its replacement. This object will have its value
modified, given a valid SET to docsDevSwServerAddress."
::= { docsDevSoftware 1 }
docsDevSwFilename OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..64))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The filename of the software image to be downloaded via
TFTP, or the abs_path (as defined in RFC 2616) of the
software image to be downloaded via HTTP.
Unless set via SNMP, this is the filename or abs_path
specified by the provisioning server during the boot
process that corresponds to the software version that
is desired for this device.
If unknown, the value of this object is the zero-length
string."
::= { docsDevSoftware 2 }
docsDevSwAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
upgradeFromMgt(1),
allowProvisioningUpgrade(2),
ignoreProvisioningUpgrade(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If set to upgradeFromMgt(1), the device will initiate a
TFTP or HTTP software image download. After
successfully receiving an image, the device will set
its state to ignoreProvisioningUpgrade(3) and reboot.
If the download process is interrupted (e.g., by a reset
or power failure), the device will load the previous
image and, after re-initialization, continue to attempt
loading the image specified in docsDevSwFilename.
If set to allowProvisioningUpgrade(2), the device will
use the software version information supplied by the
provisioning server when next rebooting (this does not
cause a reboot).
When set to ignoreProvisioningUpgrade(3), the device
will disregard software image upgrade information
from the provisioning server.
Note that reading this object can return
upgradeFromMgt(1). This indicates that a software
download is currently in progress, and that the device
will reboot after successfully receiving an image."
DEFVAL { allowProvisioningUpgrade }
::= { docsDevSoftware 3 }
docsDevSwOperStatus OBJECT-TYPE
SYNTAX INTEGER {
inProgress(1),
completeFromProvisioning(2),
completeFromMgt(3),
failed(4),
other(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"InProgress(1) indicates that a TFTP or HTTP download is
underway, either as a result of a version mismatch at
provisioning or as a result of a upgradeFromMgt request.
No other docsDevSw* objects can be modified in
this state.
CompleteFromProvisioning(2) indicates that the last
software upgrade was a result of version mismatch at
provisioning.
CompleteFromMgt(3) indicates that the last software
upgrade was a result of setting docsDevSwAdminStatus to
upgradeFromMgt.
Failed(4) indicates that the last attempted download
failed, ordinarily due to TFTP or HTTP timeout."
REFERENCE
"DOCSIS RFI 1.0 Specification, Section 8.2., and
DOCSIS RFI 1.1 Specification, Section 10.1. and
DOCSIS RFI 2.0 Specification, Section 12.1."
::= { docsDevSoftware 4 }
docsDevSwCurrentVers OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The software version currently operating in this device.
This string's syntax is that used by the
individual vendor to identify software versions.
For a CM, this string will describe the current
software load. For a CMTS, this object SHOULD contain
a human-readable representation either of the vendor
specific designation of the software for the chassis,
or of the software for the control processor. If
neither of these is applicable, the value MUST be a
zero-length string."
::= { docsDevSoftware 5 }
docsDevSwServerAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of address of the TFTP or HTTP server used for
software upgrades.
If docsDevSwServerTransportProtocol is currently set to
tftp(1), attempting to set this object to dns(16) MUST
result in an error."
::= { docsDevSoftware 6 }
docsDevSwServerAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The address of the TFTP or HTTP server used for software
upgrades.
If the TFTP/HTTP server is unknown, return the zero-
length address string (see the TextualConvention).
If docsDevSwServer is also implemented in this agent,
this object is tied to it. A set of this object to an
IPv4 address will result in also setting the value of
docsDevSwServer to that address. If this object is set
to an IPv6 address, docsDevSwServer is set to 0.0.0.0.
If docsDevSwServer is set, this object is also set to
that value. Note that if both are set in the same
action, the order of which one sets the other is
undefined."
::= { docsDevSoftware 7 }
docsDevSwServerTransportProtocol OBJECT-TYPE
SYNTAX INTEGER {
tftp(1),
http(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the transport protocol (TFTP or
HTTP) to be used for software upgrades.
If the value of this object is tftp(1), then the cable
device uses TFTP (RFC 1350) read request packets to
download the docsDevSwFilename from the
docsDevSwServerAddress in octet mode.
If the value of this object is http(2), then the cable
device uses HTTP 1.0 (RFC 1945) or HTTP 1.1 (RFC 2616)
GET requests sent to host docsDevSwServerAddress to
download the software image from path docsDevSwFilename.
If docsDevSwServerAddressType is currently set to
dns(16), attempting to set this object to tftp(1) MUST
result in an error."
DEFVAL { tftp }
::= { docsDevSoftware 8 }
--
-- The following group describes server access and parameters used
-- for initial provisioning and bootstrapping.
--
docsDevServer OBJECT IDENTIFIER ::= { docsDevMIBObjects 4 }
docsDevServerBootState OBJECT-TYPE
SYNTAX INTEGER {
operational(1),
disabled(2),
waitingForDhcpOffer(3),
waitingForDhcpResponse(4),
waitingForTimeServer(5),
waitingForTftp(6),
refusedByCmts(7),
forwardingDenied(8),
other(9),
unknown(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If operational(1), the device has completed loading and
processing of configuration parameters, and the CMTS has
completed the Registration exchange.
If disabled(2), then the device was administratively
disabled, possibly by being refused network access in
the configuration file.
If waitingForDhcpOffer(3), then a Dynamic Host
Configuration Protocol (DHCP) Discover has been
transmitted, and no offer has yet been received.
If waitingForDhcpResponse(4), then a DHCP Request has
been transmitted, and no response has yet been received.
If waitingForTimeServer(5), then a Time Request has been
transmitted, and no response has yet been received.
If waitingForTftp(6), then a request to the TFTP
parameter server has been made, and no response
received.
If refusedByCmts(7), then the Registration
Request/Response exchange with the CMTS failed.
If forwardingDenied(8), then the registration process
was completed, but the network access option in the
received configuration file prohibits forwarding.
If other(9), then the registration process reached a
point that does not fall into one of the above
categories.
If unknown(10), then the device has not yet begun the
registration process or is in some other indeterminate
state."
REFERENCE
"DOCSIS RFI 1.0 Specification, Figure 7-1, and
DOCSIS RFI 1.1 Specification, Figure 9-1 and
DOCSIS RFI 2.0 Specification, Figure 11-1."
::= { docsDevServer 1 }
docsDevServerDhcp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The IP address of the DHCP server that assigned an IP
address to this device. Returns 0.0.0.0 if DHCP is not
used for IP address assignment, or if this agent is
not assigned an IPv4 address.
This object is deprecated and is replaced by
docsDevServerDhcpAddress."
::= { docsDevServer 2 }
docsDevServerTime OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The IP address of the Time server (RFC 0868). Returns
0.0.0.0 if the time server IP address is unknown, or if
the time server is not an IPv4 server.
This object is deprecated and is replaced by
docsDevServerTimeAddress."
::= { docsDevServer 3 }
docsDevServerTftp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The IP address of the TFTP server responsible for
downloading provisioning and configuration parameters
to this device. Returns 0.0.0.0 if the TFTP server
address is unknown or is not an IPv4 address.
This object is deprecated and is replaced by
docsDevServerConfigTftpAddress."
::= { docsDevServer 4 }
docsDevServerConfigFile OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the device configuration file read from
the TFTP server. Returns a zero-length string if
the configuration file name is unknown."
::= { docsDevServer 5 }
docsDevServerDhcpAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of address of docsDevServerDhcpAddress. If
DHCP was not used, this value should return
unknown(0)."
::= { docsDevServer 6 }
docsDevServerDhcpAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internet address of the DHCP server that assigned
an IP address to this device. Returns the zero length
octet string if DHCP was not used for IP address
assignment."
::= { docsDevServer 7 }
docsDevServerTimeAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of address of docsDevServerTimeAddress. If
no time server exists, this value should return
unknown(0)."
::= { docsDevServer 8 }
docsDevServerTimeAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Internet address of the RFC 868 Time server,
as provided by DHCP option 4.
Note that if multiple values are provided to the
CM in DHCP option 4, the value of this MIB object
MUST be the Time server address from which the Time
of Day reference was acquired as based on the DOCSIS
RFI specification. During the period of time where
the Time of Day have not been acquired, the Time
server address reported by the CM may report the
first address value in the DHCP option value or the
last server address the CM attempted to get the Time
of day value.
Returns the zero-length octet string if the time server
IP address is not provisioned."
REFERENCE
"DOCSIS RFI 1.1 Specification, Section 9.2.7. and
DOCSIS RFI 2.0 Specification, Section 11.2.7."
::= { docsDevServer 9 }
docsDevServerConfigTftpAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of address of docsDevServerConfigTftpAddress.
If no TFTP server exists, this value should return
unknown(0)."
::= { docsDevServer 10 }
docsDevServerConfigTftpAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The internet address of the TFTP server responsible for
downloading provisioning and configuration parameters
to this device. Returns the zero-length octet string if
the config server address is unknown. There are certain
security risks that are involved with using TFTP."
REFERENCE
"RFC 3617, Section 5"
::= { docsDevServer 11 }
--
-- Event Reporting
--
docsDevEvent OBJECT IDENTIFIER ::= { docsDevMIBObjects 5 }
docsDevEvControl OBJECT-TYPE
SYNTAX INTEGER {
resetLog(1),
useDefaultReporting(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to resetLog(1) empties the event
log. All data is deleted. Setting it to
useDefaultReporting(2) returns all event priorities to
their factory-default reporting. Reading this object
always returns useDefaultReporting(2)."
::= { docsDevEvent 1 }
docsDevEvSyslog OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The IP address of the Syslog server. If 0.0.0.0, either
syslog transmission is inhibited, or the Syslog server
address is not an IPv4 address.
This object is deprecated and is replaced by
docsDevEvSyslogAddress."
::= { docsDevEvent 2 }
docsDevEvThrottleAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
unconstrained(1),
maintainBelowThreshold(2),
stopAtThreshold(3),
inhibited(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Controls the transmission of traps and syslog messages
with respect to the trap pacing threshold.
unconstrained(1) causes traps and syslog messages to be
transmitted without regard to the threshold settings.
maintainBelowThreshold(2) causes trap transmission and
syslog messages to be suppressed if the number of traps
would otherwise exceed the threshold.
stopAtThreshold(3) causes trap transmission to cease at
the threshold and not to resume until directed to do so.
inhibited(4) causes all trap transmission and syslog
messages to be suppressed.
A single event is always treated as a single event for
threshold counting. That is, an event causing both a
trap and a syslog message is still treated as a single
event.
Writing to this object resets the thresholding state."
DEFVAL { unconstrained }
::= { docsDevEvent 3 }
docsDevEvThrottleInhibited OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"If true(1), trap and syslog transmission is currently
inhibited due to thresholds and/or the current setting
of docsDevEvThrottleAdminStatus. In addition, this is
true(1) when transmission is inhibited because no
syslog (docsDevEvSyslog) or trap (docsDevNmAccessEntry)
destinations have been set.
This object is deprecated and is replaced by
docsDevEvThrottleThresholdExceeded."
::= { docsDevEvent 4 }
docsDevEvThrottleThreshold OBJECT-TYPE
SYNTAX Unsigned32
UNITS "events"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Number of events per docsDevEvThrottleInterval permitted
before throttling is to occur.
A single event, whether the notification could result in
messages transmitted using syslog, SNMP, or both
protocols, and regardless of the number of destinations,
(including zero) is always treated as a single event for
threshold counting. For example, an event causing both
a trap and a syslog message is still treated as a single
event.
All system notifications that occur within the device
should be taken into consideration when calculating
and monitoring the threshold."
DEFVAL { 0 }
::= { docsDevEvent 5 }
docsDevEvThrottleInterval OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The interval over which docsDevEvThrottleThreshold
applies."
DEFVAL { 1 }
::= { docsDevEvent 6 }
--
-- The following table controls the reporting of the various classes
-- of events.
--
docsDevEvControlTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevEvControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table allows control of the reporting of event
classes. For each event priority, a combination of
logging and reporting mechanisms may be chosen. The
mapping of event types to priorities is
vendor dependent. Vendors may also choose to allow
the user to control that mapping through proprietary
means. Table entries MUST persist across reboots for
CMTS devices and MUST NOT persist across reboots for CM
devices."
::= { docsDevEvent 7 }
docsDevEvControlEntry OBJECT-TYPE
SYNTAX DocsDevEvControlEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Allows configuration of the reporting mechanisms for a
particular event priority."
INDEX { docsDevEvPriority }
::= { docsDevEvControlTable 1 }
DocsDevEvControlEntry ::= SEQUENCE {
docsDevEvPriority INTEGER,
docsDevEvReporting BITS
}
docsDevEvPriority OBJECT-TYPE
SYNTAX INTEGER {
emergency(1),
alert(2),
critical(3),
error(4),
warning(5),
notice(6),
information(7),
debug(8)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The priority level that is controlled by this
entry. These are ordered from most (emergency) to least
(debug) critical. Each event with a CM or CMTS has a
particular priority level associated with it (as defined
by the vendor).
emergency(1) events indicate vendor-specific fatal
hardware or software errors that prevent normal system
operation.
alert(2) events indicate a serious failure that causes
the reporting system to reboot but is not caused by
hardware or software malfunctioning.
critical(3) events indicate a serious failure that
requires attention and prevents the device from
transmitting data but that could be recovered without
rebooting the system.
error(4) and warning(5) events indicate that a failure
occurred that could interrupt the normal data flow but
that does not cause the device to re-register.
notice(6) and information(7) events indicate a
milestone or checkpoint in normal operation that could
be of particular importance for troubleshooting.
debug(8) events are reserved for vendor-specific
events.
During normal operation, no event more
critical than notice(6) should be generated. Events
between warning and emergency should be generated at
appropriate levels of problems (e.g., emergency when the
box is about to crash)."
::= { docsDevEvControlEntry 1 }
docsDevEvReporting OBJECT-TYPE
SYNTAX BITS {
local(0),
traps(1),
syslog(2),
-- The following are extensions to the original set of
-- labels. The extensions start at an octet boundary.
-- So for bits 3 - 7, one MUST set them to zero on send
-- and one MUST ignore them on receipt.
localVolatile(8),
stdInterface(9)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Defines the action to be taken on occurrence of this
event class. Implementations may not necessarily
support all options for all event classes but at
minimum must allow traps and syslogging to be
disabled.
If the local(0) bit is set, then log to the internal
log and update non-volatile store, for backward
compatibility with the original RFC 2669 definition.
If the traps(1) bit is set, then generate
an SNMP trap; if the syslog(2) bit is set, then
send a syslog message (assuming that the syslog address
is set). If the localVolatile(8) bit is set, then
log to the internal log without updating non-volatile
store. If the stdInterface(9) bit is set, then the
agent ignores all other bits except the local(0),
syslog(2), and localVolatile(8) bits. Setting the
stdInterface(9) bit indicates that RFC3413 and
RFC3014 are being used to control event reporting
mechanisms."
::= { docsDevEvControlEntry 2 }
docsDevEventTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevEventEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Contains a log of network and device events that may be
of interest in fault isolation and troubleshooting.
If the local(0) bit is set in docsDevEvReporting,
entries in this table MUST persist across reboots."
::= { docsDevEvent 8 }
docsDevEventEntry OBJECT-TYPE
SYNTAX DocsDevEventEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes a network or device event that may be of
interest in fault isolation and troubleshooting.
Multiple sequential identical events are represented by
incrementing docsDevEvCounts and setting
docsDevEvLastTime to the current time rather than
creating multiple rows.
Entries are created with the first occurrence of an
event. docsDevEvControl can be used to clear the
table. Individual events cannot be deleted."
INDEX { docsDevEvIndex }
::= { docsDevEventTable 1 }
DocsDevEventEntry ::= SEQUENCE {
docsDevEvIndex Integer32,
docsDevEvFirstTime DateAndTime,
docsDevEvLastTime DateAndTime,
docsDevEvCounts Counter32,
docsDevEvLevel INTEGER,
docsDevEvId Unsigned32,
docsDevEvText SnmpAdminString
}
docsDevEvIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Provides relative ordering of the objects in the event
log. This object will always increase except when
(a) the log is reset via docsDevEvControl,
(b) the device reboots and does not implement
non-volatile storage for this log, or (c) it reaches
the value 2^31. The next entry for all the above
cases is 1."
::= { docsDevEventEntry 1 }
docsDevEvFirstTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of docsDevDateTime at the time this entry was
created."
::= { docsDevEventEntry 2 }
docsDevEvLastTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When an entry reports only one event, this object will
have the same value as the corresponding instance of
docsDevEvFirstTime. When an entry reports multiple
events, this object will record the value that
docsDevDateTime had when the most recent event for this
entry occurred."
::= { docsDevEventEntry 3 }
-- This object was renamed from docsDevEvCount to meet naming
-- requirements for Counter32
docsDevEvCounts OBJECT-TYPE
SYNTAX Counter32
UNITS "events"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of consecutive event instances reported by
this entry. This starts at 1 with the creation of this
row and increments by 1 for each subsequent duplicate
event."
::= { docsDevEventEntry 4 }
docsDevEvLevel OBJECT-TYPE
SYNTAX INTEGER {
emergency(1),
alert(2),
critical(3),
error(4),
warning(5),
notice(6),
information(7),
debug(8)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The priority level of this event, as defined by the
vendor. These are ordered from most serious (emergency)
to least serious (debug).
emergency(1) events indicate vendor-specific fatal
hardware or software errors that prevent normal system
operation.
alert(2) events indicate a serious failure that causes
the reporting system to reboot but that is not caused by
hardware or software malfunctioning.
critical(3) events indicate a serious failure that
requires attention and prevents the device from
transmitting data but that could be recovered without
rebooting the system.
error(4) and warning(5) events indicate that a failure
occurred that could interrupt the normal data flow but
that does not cause the device to re-register.
notice(6) and information(7) events indicate a
milestone or checkpoint in normal operation that could
be of particular importance for troubleshooting.
debug(8) events are reserved for vendor-specific
events.
During normal operation, no event more
critical than notice(6) should be generated. Events
between warning and emergency should be generated at
appropriate levels of problems (e.g., emergency when the
box is about to crash)."
::= { docsDevEventEntry 5 }
--
-- It is strongly recommended that implementors follow the CableLabs
-- enumerations for docsDevEvId, per the DOCSIS OSSIv1.1 spec
-- and follow-on specifications.
--
docsDevEvId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For this product, uniquely identifies the type of event
that is reported by this entry."
REFERENCE
"DOCSIS OSSI 1.1 Specification, Appendix H and
DOCSIS OSSI 2.0 Specification, Annex D."
::= { docsDevEventEntry 6 }
docsDevEvText OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides a human-readable description of the event,
including all relevant context (interface numbers,
etc.)."
::= { docsDevEventEntry 7 }
docsDevEvSyslogAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The type of address of docsDevEvSyslogAddress. If
no syslog server exists, this value should return
unknown(0)."
DEFVAL { unknown }
::= { docsDevEvent 9 }
docsDevEvSyslogAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The Internet address of the Syslog server, as provided
by DHCP option 7 or set via SNMP management. If the
address of the server is set to the zero-length
string, the 0.0.0.0 IPv4 address, or the 0: IPv6
address, Syslog transmission is inhibited.
Note that if multiple values are provided to the CM in
DHCP option 7, the value of this MIB object MUST be the
first Syslog server address received.
By default at agent boot, this object returns the zero
length string."
::= { docsDevEvent 10 }
docsDevEvThrottleThresholdExceeded OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"If true(1), trap and syslog transmission is currently
inhibited due to exceeding the trap/syslog event
threshold in the current interval."
::= { docsDevEvent 11 }
--
-- Link Level Control Filtering
--
docsDevFilter OBJECT IDENTIFIER ::= { docsDevMIBObjects 6 }
docsDevFilterLLCUnmatchedAction OBJECT-TYPE
SYNTAX INTEGER {
discard(1),
accept(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"LLC (Link Level Control) filters can be defined on an
inclusive or exclusive basis: CMs can be configured to
forward only packets matching a set of layer three
protocols, or to drop packets matching a set of layer
three protocols. Typical use of these filters is to
filter out possibly harmful (given the context of a
large metropolitan LAN) protocols.
If set to discard(1), any L2 packet that does not match
at least one filter in the docsDevFilterLLCTable will be
discarded. If set to accept(2), any L2 packet that
does not match at least one filter in the
docsDevFilterLLCTable will be accepted for further
processing (e.g., bridging). In other words, if the
packet does not match an entry in the table, it takes
this action; if it does match an entry in the table, it
takes the opposite of this action."
DEFVAL { accept }
::= { docsDevFilter 1 }
docsDevFilterLLCTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevFilterLLCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A list of filters to apply to (bridged) LLC
traffic. The filters in this table are applied to
incoming traffic on the appropriate interface(s) prior
to any further processing (e.g., before the packet
is handed off for level 3 processing, or for bridging).
The specific action taken when no filter is matched is
controlled by docsDevFilterLLCUnmatchedAction. Table
entries MUST NOT persist across reboots for any device."
::= { docsDevFilter 2 }
docsDevFilterLLCEntry OBJECT-TYPE
SYNTAX DocsDevFilterLLCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes a single filter to apply to (bridged) LLC
traffic received on a specified interface. "
INDEX { docsDevFilterLLCIndex }
::= { docsDevFilterLLCTable 1 }
DocsDevFilterLLCEntry ::= SEQUENCE {
docsDevFilterLLCIndex Integer32,
docsDevFilterLLCStatus RowStatus,
docsDevFilterLLCIfIndex InterfaceIndexOrZero,
docsDevFilterLLCProtocolType INTEGER,
docsDevFilterLLCProtocol Integer32,
docsDevFilterLLCMatches Counter32
}
docsDevFilterLLCIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index used for the identification of filters (note that
LLC filter order is irrelevant)."
::= { docsDevFilterLLCEntry 1 }
docsDevFilterLLCStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Controls and reflects the status of rows in this
table. There is no restriction on changing any of the
associated columns for this row while this object is set
to active.
Specifying only this object (with the
appropriate index) on a CM is sufficient to create a
filter row that matches all inbound packets on the
ethernet interface and results in the packets being
discarded. docsDevFilterLLCIfIndex (at least) must be
specified on a CMTS to create a row."
::= { docsDevFilterLLCEntry 2}
docsDevFilterLLCIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The entry interface to which this filter applies. The
value corresponds to ifIndex for either a CATV MAC or
another network interface. If the value is zero, the
filter applies to all interfaces. In Cable Modems, the
default value is the customer side interface(s). In
CMTSs, this object has to be specified to
create a row in this table.
Note that according to the DOCSIS OSSIv1.1
specification, ifIndex '1' in the CM means that this
row applies to all Cable Modem-to-CPE Interfaces
(CMCI)."
REFERENCE
"DOCSIS OSSI 1.1 Specification, Section 3.3.4.1. and
DOCSIS OSSI 2.0 Specification, Section 6.3.4.1."
::= { docsDevFilterLLCEntry 3 }
docsDevFilterLLCProtocolType OBJECT-TYPE
SYNTAX INTEGER {
ethertype(1),
dsap(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The format of the value in docsDevFilterLLCProtocol:
either a two-byte Ethernet Ethertype, or a one-byte
802.2 Service Access Point (SAP) value. ethertype(1)
also applies to Standard Network Access Protocol
(SNAP) encapsulated frames."
DEFVAL { ethertype }
::= { docsDevFilterLLCEntry 4 }
docsDevFilterLLCProtocol OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The layer-three protocol for which this filter applies.
The protocol value format depends on
docsDevFilterLLCProtocolType. Note that for SNAP
frames, ethertype filtering is performed rather than
Destination Service Access Point (DSAP) =0xAA."
DEFVAL { 0 }
::= { docsDevFilterLLCEntry 5 }
docsDevFilterLLCMatches OBJECT-TYPE
SYNTAX Counter32
UNITS "matches"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Counts the number of times this filter was matched."
::= { docsDevFilterLLCEntry 6 }
--
-- IPv4 Filtering
--
docsDevFilterIpDefault OBJECT-TYPE
SYNTAX INTEGER {
discard(1),
accept(2)
}
MAX-ACCESS read-write
STATUS deprecated
DESCRIPTION
"The default behavior for (bridged) packets that do not
match IP filters (or Internet filters, if implemented)
is defined by docsDevFilterIpDefault.
If set to discard(1), all packets not matching an IP
filter in docsDevFilterIpTable will be discarded. If
set to accept(2), all packets not matching an IP filter
or an Internet filter will be accepted for further
processing (e.g., bridging)."
DEFVAL { accept }
::= { docsDevFilter 3 }
docsDevFilterIpTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevFilterIpEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An ordered list of filters or classifiers to apply to
IP traffic. Filter application is ordered by the filter
index, rather than by a best match algorithm (note that
this implies that the filter table may have gaps in the
index values). Packets that match no filters will have
policy 0 in the docsDevFilterPolicyTable applied to
them, if it exists. Otherwise, Packets that match no
filters are discarded or forwarded according to the
setting of docsDevFilterIpDefault.
Any IP packet can theoretically match multiple rows of
this table. When considering a packet, the table is
scanned in row index order (e.g., filter 10 is checked
before filter 20). If the packet matches that filter
(which means that it matches ALL criteria for that row),
actions appropriate to docsDevFilterIpControl and
docsDevFilterPolicyId are taken. If the packet was
discarded processing is complete. If
docsDevFilterIpContinue is set to true, the filter
comparison continues with the next row in the table,
looking for additional matches.
If the packet matches no filter in the table, the packet
is accepted or dropped for further processing
according to the setting of docsDevFilterIpDefault.
If the packet is accepted, the actions specified by
policy group 0 (e.g., the rows in
docsDevFilterPolicyTable that have a value of 0 for
docsDevFilterPolicyId) are taken, if that policy
group exists.
Logically, this table is consulted twice during the
processing of any IP packet: once upon its acceptance
from the L2 entity, and once upon its transmission to
the L2 entity. In actuality, for cable modems, IP
filtering is generally the only IP processing done for
transit traffic. This means that inbound and outbound
filtering can generally be done at the same time with
one pass through the filter table.
The objects in this table are only accessible from cable
devices that are not operating in DiffServ MIB mode
(RFC 3289). See the conformance section for details.
Note that some devices are required by other
specifications (e.g., the DOCSIS OSSIv1.1 specification)
to support the legacy SNMPv1/v2c docsDevFilter mode
for backward compatibility.
Table entries MUST NOT persist across reboots for any
device.
This table is deprecated. Instead, use the DiffServ MIB
from RFC 3289."
::= { docsDevFilter 4 }
docsDevFilterIpEntry OBJECT-TYPE
SYNTAX DocsDevFilterIpEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Describes a filter to apply to IP traffic received on a
specified interface. All identity objects in this table
(e.g., source and destination address/mask, protocol,
source/dest port, TOS/mask, interface and direction)
must match their respective fields in the packet for
any given filter to match.
To create an entry in this table, docsDevFilterIpIfIndex
must be specified."
INDEX { docsDevFilterIpIndex }
::= { docsDevFilterIpTable 1 }
DocsDevFilterIpEntry ::= SEQUENCE {
docsDevFilterIpIndex Integer32,
docsDevFilterIpStatus RowStatus,
docsDevFilterIpControl INTEGER,
docsDevFilterIpIfIndex InterfaceIndexOrZero,
docsDevFilterIpDirection INTEGER,
docsDevFilterIpBroadcast TruthValue,
docsDevFilterIpSaddr IpAddress,
docsDevFilterIpSmask IpAddress,
docsDevFilterIpDaddr IpAddress,
docsDevFilterIpDmask IpAddress,
docsDevFilterIpProtocol Integer32,
docsDevFilterIpSourcePortLow Integer32,
docsDevFilterIpSourcePortHigh Integer32,
docsDevFilterIpDestPortLow Integer32,
docsDevFilterIpDestPortHigh Integer32,
docsDevFilterIpMatches ZeroBasedCounter32,
docsDevFilterIpTos OCTET STRING,
docsDevFilterIpTosMask OCTET STRING,
docsDevFilterIpContinue TruthValue,
docsDevFilterIpPolicyId Integer32
}
docsDevFilterIpIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Index used to order the application of filters.
The filter with the lowest index is always applied
first."
::= { docsDevFilterIpEntry 1 }
docsDevFilterIpStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Controls and reflects the status of rows in this
table. Specifying only this object (with the
appropriate index) on a CM is sufficient to create a
filter row that matches all inbound packets on the
ethernet interface and results in the packets being
discarded. docsDevFilterIpIfIndex (at least) must be
specified on a CMTS to create a row. Creation of the
rows may be done via either create-and-wait or
create-and-go, but the filter is not applied until this
object is set to (or changes to) active. There is no
restriction in changing any object in a row while this
object is set to active."
::= { docsDevFilterIpEntry 2 }
docsDevFilterIpControl OBJECT-TYPE
SYNTAX INTEGER {
discard(1),
accept(2),
policy(3)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If set to discard(1), all packets matching this filter
will be discarded, and scanning of the remainder of the
filter list will be aborted. If set to accept(2), all
packets matching this filter will be accepted for
further processing (e.g., bridging). If
docsDevFilterIpContinue is set to true, see if there
are other matches; otherwise, done. If set to
policy (3), execute the policy entries
matched by docsDevFilterIpPolicyId in
docsDevFilterPolicyTable.
If docsDevFilterIpContinue is set to true, continue
scanning the table for other matches; otherwise, done."
DEFVAL { discard }
::= { docsDevFilterIpEntry 3 }
docsDevFilterIpIfIndex OBJECT-TYPE
SYNTAX InterfaceIndexOrZero
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The entry interface to which this filter applies. The
value corresponds to ifIndex for either a CATV MAC or
another interface. If the value is zero, the
filter applies to all interfaces. Default value in CMs
is the index of the customer-side (e.g., ethernet)
interface(s). In CMTSes, this object MUST be
specified to create a row in this table.
Note that according to the DOCSIS OSSIv1.1
specification, ifIndex '1' in the Cable Modem means
that this row applies to all CMCI (customer-facing)
interfaces."
REFERENCE
"DOCSIS OSSI 1.1 Specification, Section 3.3.4.1. and
DOCSIS OSSI 2.0 Specification, Section 6.3.4.1."
::= { docsDevFilterIpEntry 4 }
docsDevFilterIpDirection OBJECT-TYPE
SYNTAX INTEGER {
inbound(1),
outbound(2),
both(3)
}
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Determines whether the filter is applied to inbound(1)
traffic, outbound(2) traffic, or traffic in both(3)
directions."
DEFVAL { inbound }
::= { docsDevFilterIpEntry 5 }
docsDevFilterIpBroadcast OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If set to true(1), the filter only applies to multicast
and broadcast traffic. If set to false(2), the filter
applies to all traffic."
DEFVAL { false }
::= { docsDevFilterIpEntry 6 }
docsDevFilterIpSaddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The source IP address, or portion thereof, that is to be
matched for this filter. The source address is first
masked (ANDed) against docsDevFilterIpSmask before
being compared to this value. A value of 0 for this
object and 0 for the mask matches all IP addresses."
DEFVAL { '00000000'h }
::= { docsDevFilterIpEntry 7 }
docsDevFilterIpSmask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"A bit mask that is to be applied to the source address
prior to matching. This mask is not necessarily the
same as a subnet mask, but 1s bits must be leftmost and
contiguous."
DEFVAL { '00000000'h }
::= { docsDevFilterIpEntry 8 }
docsDevFilterIpDaddr OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The destination IP address, or portion thereof, that is
to be matched for this filter. The destination address
is first masked (ANDed) against docsDevFilterIpDmask
before being compared to this value. A value of
00000000 for this object and 00000000 for the mask
matches all IP addresses."
DEFVAL { '00000000'h }
::= { docsDevFilterIpEntry 9 }
docsDevFilterIpDmask OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"A bit mask that is to be applied to the destination
address prior to matching. This mask is not necessarily
the same as a subnet mask, but 1s bits MUST be leftmost
and contiguous."
DEFVAL { '00000000'h }
::= { docsDevFilterIpEntry 10 }
docsDevFilterIpProtocol OBJECT-TYPE
SYNTAX Integer32 (0..256)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The IP protocol value that is to be matched. For
example, icmp is 1, tcp is 6, and udp is 17. A value of
256 matches ANY protocol."
REFERENCE "www.iana.org/assignments/protocol-numbers"
DEFVAL { 256 }
::= { docsDevFilterIpEntry 11 }
docsDevFilterIpSourcePortLow OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the inclusive lower bound of the transport-layer
source port range that is to be matched. If the IP
protocol of the packet is neither UDP nor TCP, this
object is ignored during matching."
REFERENCE "www.iana.org/assignments/port-numbers"
DEFVAL { 0 }
::= { docsDevFilterIpEntry 12 }
docsDevFilterIpSourcePortHigh OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the inclusive upper bound of the transport-layer
source port range that is to be matched. If the IP
protocol of the packet is neither UDP nor TCP, this
object is ignored during matching."
REFERENCE "www.iana.org/assignments/port-numbers"
DEFVAL { 65535 }
::= { docsDevFilterIpEntry 13 }
docsDevFilterIpDestPortLow OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the inclusive lower bound of the transport-layer
destination port range that is to be matched. If the IP
protocol of the packet is neither UDP nor TCP, this
object is ignored during matching."
REFERENCE "www.iana.org/assignments/port-numbers"
DEFVAL { 0 }
::= { docsDevFilterIpEntry 14 }
docsDevFilterIpDestPortHigh OBJECT-TYPE
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the inclusive upper bound of the transport-layer
destination port range that is to be matched. If the IP
protocol of the packet is neither UDP nor TCP, this
object is ignored during matching."
REFERENCE "www.iana.org/assignments/port-numbers"
DEFVAL { 65535 }
::= { docsDevFilterIpEntry 15 }
docsDevFilterIpMatches OBJECT-TYPE
SYNTAX ZeroBasedCounter32
UNITS "matches"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Counts the number of times this filter was matched.
This object is initialized to 0 at boot, or at row
creation, and is reset only upon reboot."
::= { docsDevFilterIpEntry 16 }
docsDevFilterIpTos OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This is the value to be matched to the packet's
TOS (Type of Service) value (after the TOS value
is ANDed with docsDevFilterIpTosMask). A value for this
object of 0 and a mask of 0 matches all TOS values."
DEFVAL { '00'h }
::= { docsDevFilterIpEntry 17 }
docsDevFilterIpTosMask OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The mask to be applied to the packet's TOS value before
matching."
DEFVAL { '00'h }
::= { docsDevFilterIpEntry 18 }
docsDevFilterIpContinue OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"If this value is set to true and docsDevFilterIpControl
is anything but discard (1), continue scanning and
applying policies. See Section 3.3.3 for more
details."
DEFVAL { false }
::= { docsDevFilterIpEntry 19 }
docsDevFilterIpPolicyId OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object points to an entry in
docsDevFilterPolicyTable. If docsDevFilterIpControl
is set to policy (3), execute all matching policies
in docsDevFilterPolicyTable. If no matching policy
exists, treat as if docsDevFilterIpControl were set
to accept (1). If this object is set to the value of
0, there is no matching policy, and
docsDevFilterPolicyTable MUST NOT be consulted."
DEFVAL { 0 }
::= { docsDevFilterIpEntry 20 }
--
-- Policy Mapping Table
--
docsDevFilterPolicyTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevFilterPolicyEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"A Table that maps between a policy group ID and a set
of pointers to policies to be applied. All rows with
the same docsDevFilterPolicyId are part of the same
group of policy pointers and are applied in the order
in this table. docsDevFilterPolicyTable exists to
allow multiple policy actions (referenced by policy
pointers) to be applied to any given classified packet.
The policy actions are applied in index order.
For example:
Index ID Type Action
1 1 TOS 1
9 5 TOS 1
12 1 IPSEC 3
This says that a packet that matches a filter with
policy id 1 first has TOS policy 1 applied (which might
set the TOS bits to enable a higher priority) and next
has the IPSEC policy 3 applied (which may result in the
packets being dumped into a secure VPN to a remote
encryptor).
Policy ID 0 is reserved for default actions and is
applied only to packets that match no filters in
docsDevFilterIpTable.
Table entries MUST NOT persist across reboots for any
device.
This table is deprecated. Instead, use the DiffServ MIB
from RFC 3289."
::= { docsDevFilter 5 }
docsDevFilterPolicyEntry OBJECT-TYPE
SYNTAX DocsDevFilterPolicyEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry in the docsDevFilterPolicyTable. Entries are
created by Network Management. To create an entry,
docsDevFilterPolicyId MUST be specified."
INDEX { docsDevFilterPolicyIndex }
::= { docsDevFilterPolicyTable 1 }
DocsDevFilterPolicyEntry ::= SEQUENCE {
docsDevFilterPolicyIndex Integer32,
docsDevFilterPolicyId Integer32,
-- docsDevFilterPolicyType INTEGER,
-- docsDevFilterPolicyAction Integer32,
docsDevFilterPolicyStatus RowStatus,
docsDevFilterPolicyPtr RowPointer
}
docsDevFilterPolicyIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION "Index value for the table."
::= { docsDevFilterPolicyEntry 1 }
docsDevFilterPolicyId OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Policy ID for this entry. If a policy ID can apply to
multiple rows of this table, all relevant policies are
executed. Policy 0 (if populated) is applied to all
packets that do not match any of the filters. N.B. If
docsDevFilterIpPolicyId is set to 0, it DOES NOT match
policy 0 of this table."
::= { docsDevFilterPolicyEntry 2 }
-- The following two objects were removed and never used; however,
-- to preserve OID numbering, they are simply commented out to
-- to ensure that they are not used again.
-- docsDevFilterPolicyType ::= { docsDevFilterPolicyEntry 3 }
-- docsDevFilterPolicyAction ::= { docsDevFilterPolicyEntry 4 }
docsDevFilterPolicyStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Object used to create an entry in this table. There is
no restriction in changing any object in a row while
this object is set to active.
The following object MUST have a valid value before this
object can be set to active: docsDevFilterPolicyPtr."
::= { docsDevFilterPolicyEntry 5 }
docsDevFilterPolicyPtr OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object points to a row in an applicable filter
policy table. Currently, the only standard policy
table is docsDevFilterTosTable.
Per the textual convention, this object points to the
first accessible object in the row; e.g., to point to a
row in docsDevFilterTosTable with an index of 21, the
value of this object would be the object identifier
docsDevTosStatus.21.
Vendors are recommended to adhere to the same convention
when adding vendor-specific policy table extensions.
If this pointer references an empty or non-existent
row, then no policy action is taken.
The default upon row creation is a null pointer that
results in no policy action being taken."
DEFVAL { zeroDotZero }
::= { docsDevFilterPolicyEntry 6 }
--
-- TOS Policy action table
--
docsDevFilterTosTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevFilterTosEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"Table used to describe Type of Service (TOS) bits
processing.
This table is an adjunct to the docsDevFilterIpTable
and the docsDevFilterPolicy table. Entries in the
latter table can point to specific rows in this (and
other) tables and cause specific actions to be taken.
This table permits the manipulation of the value of the
Type of Service bits in the IP header of the matched
packet as follows:
Set the tosBits of the packet to
(tosBits & docsDevFilterTosAndMask) |
docsDevFilterTosOrMask
This construct allows you to do a clear and set of all
the TOS bits in a flexible manner.
Table entries MUST NOT persist across reboots for any
device.
This table is deprecated. Instead, use the DiffServ MIB
from RFC 3289."
::= { docsDevFilter 6 }
docsDevFilterTosEntry OBJECT-TYPE
SYNTAX DocsDevFilterTosEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"A TOS policy entry."
INDEX { docsDevFilterTosIndex }
::= { docsDevFilterTosTable 1 }
DocsDevFilterTosEntry ::= SEQUENCE {
docsDevFilterTosIndex Integer32,
docsDevFilterTosStatus RowStatus,
docsDevFilterTosAndMask OCTET STRING,
docsDevFilterTosOrMask OCTET STRING
}
docsDevFilterTosIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The unique index for this row. There are no ordering
requirements for this table, and any valid index may be
specified."
::= { docsDevFilterTosEntry 1 }
docsDevFilterTosStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"The object used to create and delete entries in this
table. A row created by specifying just this object
results in a row that specifies no change to the TOS
bits. A row may be created using either the
create-and-go or create-and-wait paradigms. There is
no restriction on the ability to change values in this
row while the row is active."
::= { docsDevFilterTosEntry 2 }
docsDevFilterTosAndMask OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This value is bitwise ANDed with the matched packet's
TOS bits."
DEFVAL { 'ff'h }
::= { docsDevFilterTosEntry 3 }
docsDevFilterTosOrMask OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This value is bitwise ORed with the result from the
AND procedure (tosBits & docsDevFilterTosAndMask).
The result then replaces the packet's TOS bits."
DEFVAL { '00'h }
::= { docsDevFilterTosEntry 4 }
--
-- CPE IP Management and anti-spoofing group. Only implemented on
-- Cable Modems.
--
docsDevCpe OBJECT IDENTIFIER ::= { docsDevMIBObjects 7 }
docsDevCpeEnroll OBJECT-TYPE
SYNTAX INTEGER {
none(1),
any(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the population of
docsDevFilterCpeTable.
If set to none, the filters must be set manually
by a network management action (either configuration
or SNMP set).
If set to any, the CM wiretaps the packets originating
from the ethernet and enrolls up to docsDevCpeIpMax
addresses as based on the source IPv4 or v6 addresses of
those packets."
DEFVAL { any }
::= { docsDevCpe 1 }
docsDevCpeIpMax OBJECT-TYPE
SYNTAX Integer32 (-1..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls the maximum number of CPEs allowed
to be learned behind this device. If set to zero, any
number of CPEs may connect up to the maximum permitted
for the device.
If set to -1, no filtering is done on CPE source
addresses, and no entries are made in the
docsDevFilterCpeTable via learning. If an attempt is
made to set this to a number greater than that
permitted for the device, it is set to that maximum."
DEFVAL { -1 }
::= { docsDevCpe 2 }
docsDevCpeTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevCpeEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"This table lists the IPv4 addresses seen (or permitted)
as source addresses in packets originating from the
customer interface on this device. In addition, this
table can be provisioned with the specific addresses
permitted for the CPEs via the normal row creation
mechanisms. Table entries MUST NOT persist across
reboots for any device.
N.B. Management action can add entries in this table
and in docsDevCpeIpTable past the value of
docsDevCpeIpMax. docsDevCpeIpMax ONLY restricts the
ability of the CM to add learned addresses
automatically.
This table is deprecated and is replaced by
docsDevCpeInetTable."
::= { docsDevCpe 3 }
docsDevCpeEntry OBJECT-TYPE
SYNTAX DocsDevCpeEntry
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"An entry in the docsDevFilterCpeTable. There is one
entry for each IPv4 CPE seen or provisioned. If
docsDevCpeIpMax is set to -1, this table is ignored;
otherwise, upon receipt of an IP packet from the
customer interface of the CM, the source IP address is
checked against this table. If the address is in the
table, packet processing continues. If the address is
not in the table but docsDevCpeEnroll is set to any
and the sum of the table sizes of docsDevCpeTable and
docsDevCpeInetTable is less than docsDevCpeIpMax, the
address is added to the table, and packet processing
continues. Otherwise, the packet is dropped.
The filtering actions specified by this table occur
after any LLC filtering (docsDevFilterLLCTable), but
prior to any IP filtering (docsDevFilterIpTable,
docsDevNmAccessTable)."
INDEX { docsDevCpeIp }
::= {docsDevCpeTable 1 }
DocsDevCpeEntry ::= SEQUENCE {
docsDevCpeIp IpAddress,
docsDevCpeSource INTEGER,
docsDevCpeStatus RowStatus
}
docsDevCpeIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS deprecated
DESCRIPTION
"The IPv4 address to which this entry applies.
N.B. Attempts to set all zeros or all ones address
values MUST be rejected."
::= { docsDevCpeEntry 1 }
docsDevCpeSource OBJECT-TYPE
SYNTAX INTEGER {
other(1),
manual(2),
learned(3)
}
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"This object describes how this entry was created. If
the value is manual(2), this row was created by a
network management action (either configuration or
SNMP set). If set to learned(3), then it was found via
looking at the source IPv4 address of a received packet.
The value other(1) is used for any entries that do not
meet manual(2) or learned(3) criteria."
::= { docsDevCpeEntry 2 }
docsDevCpeStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Standard object to manipulate rows. To create a row in
this table, one only needs to specify this object.
Management stations SHOULD use the create-and-go
mechanism for creating rows in this table."
::= { docsDevCpeEntry 3 }
--
-- Internet CPE Management and anti spoofing group, for support of
-- non-IPv4 CPEs.
--
docsDevCpeInetTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsDevCpeInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table lists the IP addresses seen (or permitted) as
source addresses in packets originating from the
customer interface on this device. In addition, this
table can be provisioned with the specific addresses
permitted for the CPEs via the normal row creation
mechanisms.
N.B. Management action can add entries in this table
and in docsDevCpeIpTable past the value of
docsDevCpeIpMax. docsDevCpeIpMax ONLY restricts the
ability of the CM to add learned addresses
automatically.
Table entries MUST NOT persist across reboots for any
device.
This table exactly mirrors docsDevCpeTable and applies
to IPv4 and IPv6 addresses."
::= { docsDevCpe 4 }
docsDevCpeInetEntry OBJECT-TYPE
SYNTAX DocsDevCpeInetEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the docsDevFilterCpeInetTable. There is one
entry for each IP CPE seen or provisioned. If
docsDevCpeIpMax is set to -1, this table is ignored;
otherwise, upon receipt of an IP packet from the
customer interface of the CM, the source IP address is
checked against this table. If the address is in the
table, packet processing continues. If the address is
not in the table but docsDevCpeEnroll is set to any and
the sum of the table sizes for docsDevCpeTable and
docsDevCpeInetTable is less than docsDevCpeIpMax, the
address is added to the table, and packet processing
continues. Otherwise, the packet is dropped.
The filtering actions specified by this table occur
after any LLC filtering (docsDevFilterLLCTable), but
prior to any IP filtering (docsDevFilterIpTable,
docsDevNmAccessTable).
When an agent (cable modem) restarts, then all
dynamically created rows are lost."
INDEX { docsDevCpeInetType, docsDevCpeInetAddr }
::= { docsDevCpeInetTable 1 }
DocsDevCpeInetEntry ::= SEQUENCE {
docsDevCpeInetType InetAddressType,
docsDevCpeInetAddr InetAddress,
docsDevCpeInetSource INTEGER,
docsDevCpeInetRowStatus RowStatus
}
docsDevCpeInetType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The type of internet address of docsDevCpeInetAddr."
::= { docsDevCpeInetEntry 1 }
docsDevCpeInetAddr OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Internet address to which this entry applies.
Implementors need to be aware that if the size of
docsDevCpeInetAddr exceeds 114 octets OIDs of
instances of columns in this row will have more
than 128 sub-identifiers and cannot be accessed
using SNMPv1, SNMPv2c, or SNMPv3. Only unicast
address are allowed for this object."
::= { docsDevCpeInetEntry 2 }
docsDevCpeInetSource OBJECT-TYPE
SYNTAX INTEGER {
manual(2),
learned(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object describes how this entry was created. If
the value is manual(2), this row was created by a
network management action (either configuration or
SNMP set). If set to learned(3), then it was found
via looking at the source IP address of a received
packet."
::= { docsDevCpeInetEntry 3 }
docsDevCpeInetRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Standard object to manipulate rows. To create a row in
this table, one only needs to specify this object.
Management stations SHOULD use the create-and-go
mechanism for creating rows in this table."
::= { docsDevCpeInetEntry 4 }
--
-- Placeholder for notifications/traps.
--
-- erroneous, DO NOT USE docsDevNotification
docsDevNotification OBJECT IDENTIFIER ::= { docsDev 2 }
-- erroneous, DO NOT USE docsDevNotification
docsDevNotifications OBJECT IDENTIFIER ::= { docsDev 0 }
--
-- RFC 2669 Conformance definitions
--
docsDevConformance OBJECT IDENTIFIER ::= { docsDev 3 }
docsDevGroups OBJECT IDENTIFIER ::= { docsDevConformance 1 }
docsDevCompliances OBJECT IDENTIFIER ::= { docsDevConformance 2 }
docsDevBasicCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION
"The RFC 2669 compliance statement for MCNS/DOCSIS
Cable Modems and Cable Modem Termination Systems."
MODULE -- docsDev
-- conditionally mandatory groups
GROUP docsDevBaseGroup
DESCRIPTION
"Mandatory in Cable Modems, optional in Cable Modem
Termination Systems."
GROUP docsDevEventGroup
DESCRIPTION
"Mandatory in Cable Modems, optional in Cable Modem
Termination Systems."
GROUP docsDevFilterGroup
DESCRIPTION
"Mandatory in Cable Modems, optional in Cable Modem
Termination Systems."
GROUP docsDevNmAccessGroup
DESCRIPTION
"This group is only implemented in devices that do not
implement the SNMPv3 User Security Model. It SHOULD NOT
be implemented by devices that conform to SNMPv3.
For devices that do not implement SNMPv3 or later, this
group is Mandatory in Cable Modems and is optional
in Cable Modem Termination Systems."
GROUP docsDevServerGroup
DESCRIPTION
"This group is implemented only in Cable Modems, and is
not implemented in Cable Modem Termination Systems."
GROUP docsDevSoftwareGroup
DESCRIPTION
"This group is Mandatory in Cable Modems and optional in
Cable Modem Termination Systems."
GROUP docsDevCpeGroup
DESCRIPTION
"This group is Mandatory in Cable Modems, and is
not implemented in Cable Modem Termination Systems."
OBJECT docsDevSTPControl
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support noStFilterBpdu(2)."
OBJECT docsDevNmAccessIp
DESCRIPTION
"It is compliant to recognize the IP address
255.255.255.255 as referring to any NMS."
OBJECT docsDevEvReporting
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support local(0). An agent need not
enforce that trap or syslog logging be accompanied
by local(0) or localVolatile(3) logging."
::= { docsDevCompliances 1 }
docsDevBaseGroup OBJECT-GROUP
OBJECTS {
docsDevRole,
docsDevDateTime,
docsDevResetNow,
docsDevSerialNumber,
docsDevSTPControl
}
STATUS current
DESCRIPTION
"A collection of objects providing device status and
control."
::= { docsDevGroups 1 }
docsDevNmAccessGroup OBJECT-GROUP
OBJECTS {
docsDevNmAccessIp,
docsDevNmAccessIpMask,
docsDevNmAccessCommunity,
docsDevNmAccessControl,
docsDevNmAccessInterfaces,
docsDevNmAccessStatus
}
STATUS deprecated
DESCRIPTION
"A collection of objects for controlling access to SNMP
objects on cable devices.
This group has been deprecated because all the
objects have been deprecated in favor of SNMPv3 and
Coexistence MIBs."
::= { docsDevGroups 2 }
docsDevSoftwareGroup OBJECT-GROUP
OBJECTS {
docsDevSwServer,
docsDevSwFilename,
docsDevSwAdminStatus,
docsDevSwOperStatus,
docsDevSwCurrentVers
}
STATUS deprecated
DESCRIPTION
"A collection of objects for controlling software
downloads.
This group has been deprecated and replaced by
docsDevSoftwareGroupV2. Object docsDevSwServer
has been replaced by docsDevSwServerAddressType
and docsDevSwServerAddress, and
docsDevSwServerTransportProtocol has been added to
support TFTP and HTTP firmware downloads."
::= { docsDevGroups 3 }
docsDevServerGroup OBJECT-GROUP
OBJECTS {
docsDevServerBootState,
docsDevServerDhcp,
docsDevServerTime,
docsDevServerTftp,
docsDevServerConfigFile
}
STATUS deprecated
DESCRIPTION
"A collection of objects providing status about server
provisioning.
This group has been deprecated and replaced by
docsDevServerGroupV2. The objects docsDevServerDhcp,
docsDevServerTime, and docsDevServerTftp have
been replaced by docsDevServerDhcpAddressType,
docsDevServerDhcpAddress, docsDevServerTimeAddressType,
docsDevServerTimeAddress,
docsDevServerConfigTftpAddressType, and
docsDevServerConfigTftpAddress."
::= { docsDevGroups 4 }
docsDevEventGroup OBJECT-GROUP
OBJECTS {
docsDevEvControl,
docsDevEvSyslog,
docsDevEvThrottleAdminStatus,
docsDevEvThrottleInhibited,
docsDevEvThrottleThreshold,
docsDevEvThrottleInterval,
docsDevEvReporting,
docsDevEvFirstTime,
docsDevEvLastTime,
docsDevEvCounts,
docsDevEvLevel,
docsDevEvId,
docsDevEvText
}
STATUS deprecated
DESCRIPTION
"A collection of objects used to control and monitor
events.
This group has been deprecated and replaced by
docsDevEventGroupV2. The object docsDevEvSyslog has
been replaced by docsDevEvSyslogAddressType and
docsDevEvSyslogAddress, and docsDevEvThrottleInhibited
has been replaced by
docsDevEvThrottleThresholdExceeded."
::= { docsDevGroups 5 }
docsDevFilterGroup OBJECT-GROUP
OBJECTS {
docsDevFilterLLCUnmatchedAction,
docsDevFilterIpDefault,
docsDevFilterLLCStatus,
docsDevFilterLLCIfIndex,
docsDevFilterLLCProtocolType,
docsDevFilterLLCProtocol,
docsDevFilterLLCMatches,
docsDevFilterIpControl,
docsDevFilterIpIfIndex,
docsDevFilterIpStatus,
docsDevFilterIpDirection,
docsDevFilterIpBroadcast,
docsDevFilterIpSaddr,
docsDevFilterIpSmask,
docsDevFilterIpDaddr,
docsDevFilterIpDmask,
docsDevFilterIpProtocol,
docsDevFilterIpSourcePortLow,
docsDevFilterIpSourcePortHigh,
docsDevFilterIpDestPortLow,
docsDevFilterIpDestPortHigh,
docsDevFilterIpMatches,
docsDevFilterIpTos,
docsDevFilterIpTosMask,
docsDevFilterIpContinue,
docsDevFilterIpPolicyId,
docsDevFilterPolicyId,
docsDevFilterPolicyStatus,
docsDevFilterPolicyPtr,
docsDevFilterTosStatus,
docsDevFilterTosAndMask,
docsDevFilterTosOrMask
}
STATUS deprecated
DESCRIPTION
"A collection of objects to specify filters at the link
layer and IPv4 layer.
This group has been deprecated and replaced by various
groups from the DiffServ MIB."
::= { docsDevGroups 6 }
docsDevCpeGroup OBJECT-GROUP
OBJECTS {
docsDevCpeEnroll,
docsDevCpeIpMax,
docsDevCpeSource,
docsDevCpeStatus
}
STATUS deprecated
DESCRIPTION
"A collection of objects used to control the number
and specific values of IPv4 addresses allowed for
associated Customer Premises Equipment (CPE).
This group has been deprecated and replaced by
docsDevInetCpeGroup. The object docsDevCpeSource has
been replaced by docsDevCpeInetSource, and
docsDevCpeStatus has been replaced by
docsDevCpeInetRowStatus."
::= { docsDevGroups 7 }
--
-- RFC 4639 Conformance definitions
--
docsDevGroupsV2 OBJECT IDENTIFIER ::= { docsDevConformance 3 }
docsDevCompliancesV2 OBJECT IDENTIFIER ::= { docsDevConformance 4 }
docsDevCmCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for DOCSIS Cable Modems.
This compliance statement applies to implementations
of DOCSIS versions that are not IPv6 capable."
MODULE DIFFSERV-MIB -- RFC 3289
MANDATORY-GROUPS {
diffServMIBDataPathGroup,
diffServMIBClfrGroup,
diffServMIBClfrElementGroup,
diffServMIBMultiFieldClfrGroup,
diffServMIBActionGroup,
diffServMIBDscpMarkActGroup,
diffServMIBCounterGroup,
diffServMIBAlgDropGroup
}
OBJECT diffServDataPathStatus -- same as RFC 3289
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT diffServClfrStatus -- same as RFC 3289
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT diffServClfrElementStatus -- same as RFC 3289
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT diffServMultiFieldClfrAddrType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT diffServMultiFieldClfrSrcAddr
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT diffServMultiFieldClfrDstAddr
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT diffServAlgDropStatus -- same as RFC 3289
SYNTAX RowStatus { active(1) }
WRITE-SYNTAX RowStatus { createAndGo(4), destroy(6) }
DESCRIPTION
"Support for createAndWait and notInService is not
required."
OBJECT diffServDataPathStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServClfrStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServClfrElementStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServMultiFieldClfrStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServActionStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServCountActStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServAlgDropStorage
SYNTAX StorageType { volatile(2) }
DESCRIPTION
"An implementation is only required to support
volatile storage."
OBJECT diffServAlgDropType
SYNTAX INTEGER { alwaysDrop(5) }
DESCRIPTION
"This object is only used to provide packet
filtering. Implementations need not support other
values of this enumeration."
MODULE -- docsDev
MANDATORY-GROUPS {
docsDevBaseGroup,
docsDevBaseIgmpGroup,
docsDevBaseMaxCpeGroup,
docsDevSoftwareGroupV2,
docsDevServerGroupV2,
docsDevEventGroupV2,
docsDevFilterLLCGroup
}
-- conditionally mandatory groups
GROUP docsDevInetCpeGroup
DESCRIPTION
"This group is optional in Cable Modems."
OBJECT docsDevDateTime
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsDevSTPControl
SYNTAX INTEGER { noStFilterBpdu(2) }
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support noStFilterBpdu(2)."
OBJECT docsDevIgmpModeControl
SYNTAX INTEGER { passive(1) }
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support passive(1)."
OBJECT docsDevSwServerAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevSwServerAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerDhcpAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerDhcpAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerTimeAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerTimeAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerConfigTftpAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevServerConfigTftpAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevEvReporting
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support local(0)."
OBJECT docsDevEvSyslogAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevEvSyslogAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevSwServerTransportProtocol
SYNTAX INTEGER { tftp(1) }
DESCRIPTION
"An implementation is only required to support TFTP
software image downloads."
::= { docsDevCompliancesV2 1 }
docsDevCmtsCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for DOCSIS Cable Modem
Termination Systems.
This compliance statement applies to implementations
of DOCSIS versions that are not IPv6 capable."
MODULE -- docsDev
-- conditionally mandatory groups
GROUP docsDevBaseGroup
DESCRIPTION
"Optional in Cable Modem Termination Systems."
GROUP docsDevBaseIgmpGroup
DESCRIPTION
"Optional in Cable Modem Termination Systems."
GROUP docsDevBaseMaxCpeGroup
DESCRIPTION
"This group MUST NOT be implemented in Cable Modem
Termination Systems."
GROUP docsDevSoftwareGroupV2
DESCRIPTION
"Optional in Cable Modem Termination Systems."
GROUP docsDevServerGroupV2
DESCRIPTION
"This group MUST NOT be implemented in Cable Modem
Termination Systems."
GROUP docsDevEventGroupV2
DESCRIPTION
"Optional in Cable Modem Termination Systems."
GROUP docsDevFilterLLCGroup
DESCRIPTION
"This group MUST NOT be implemented in Cable Modem
Termination Systems. See the Subscriber Management
MIB for similar CMTS capability."
GROUP docsDevInetCpeGroup
DESCRIPTION
"This group MUST NOT be implemented in Cable Modem
Termination Systems. See the Subscriber Management
MIB for similar CMTS capability."
OBJECT docsDevDateTime
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only."
OBJECT docsDevSTPControl
SYNTAX INTEGER { noStFilterBpdu(2) }
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support noStFilterBpdu(2)."
OBJECT docsDevIgmpModeControl
SYNTAX INTEGER { passive(1) }
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support passive(1)."
OBJECT docsDevSwServerAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevSwServerAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevEvReporting
MIN-ACCESS read-only
DESCRIPTION
"It is compliant to implement this object as read-only.
Devices need only support local(0)."
OBJECT docsDevEvSyslogAddressType
SYNTAX InetAddressType { ipv4(1) }
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevEvSyslogAddress
SYNTAX InetAddress (SIZE(4))
DESCRIPTION
"An implementation is only required to support IPv4
addresses."
OBJECT docsDevSwServerTransportProtocol
SYNTAX INTEGER { tftp(1) }
DESCRIPTION
"An implementation is only required to support TFTP
software image downloads."
::= { docsDevCompliancesV2 2 }
docsDevBaseIgmpGroup OBJECT-GROUP
OBJECTS {
docsDevIgmpModeControl
}
STATUS current
DESCRIPTION
"An object providing cable device IGMP status and
control."
::= { docsDevGroupsV2 1 }
docsDevBaseMaxCpeGroup OBJECT-GROUP
OBJECTS {
docsDevMaxCpe
}
STATUS current
DESCRIPTION
"An object providing management of the maximum number of
CPEs permitted access through a cable modem."
::= { docsDevGroupsV2 2 }
docsDevNmAccessExtGroup OBJECT-GROUP
OBJECTS {
docsDevNmAccessTrapVersion
}
STATUS deprecated
DESCRIPTION
"An object, in addition to the objects in
docsDevNmAccessGroup, for controlling access to
SNMP objects on cable devices.
This group is included in this MIB due to existing
implementations of docsDevNmAccessTrapVersion in
DOCSIS cable modems.
This group has been deprecated because the object has
been deprecated in favor of SNMPv3 and Coexistence
MIBs."
::= { docsDevGroupsV2 3 }
docsDevSoftwareGroupV2 OBJECT-GROUP
OBJECTS {
docsDevSwFilename,
docsDevSwAdminStatus,
docsDevSwOperStatus,
docsDevSwCurrentVers,
docsDevSwServerAddressType,
docsDevSwServerAddress,
docsDevSwServerTransportProtocol
}
STATUS current
DESCRIPTION
"A collection of objects for controlling software
downloads. This group replaces docsDevSoftwareGroup."
::= { docsDevGroupsV2 4 }
docsDevServerGroupV2 OBJECT-GROUP
OBJECTS {
docsDevServerBootState,
docsDevServerDhcpAddressType,
docsDevServerDhcpAddress,
docsDevServerTimeAddressType,
docsDevServerTimeAddress,
docsDevServerConfigTftpAddressType,
docsDevServerConfigTftpAddress,
docsDevServerConfigFile
}
STATUS current
DESCRIPTION
"A collection of objects providing status about server
provisioning. This group replaces docsDevServerGroup."
::= { docsDevGroupsV2 5 }
docsDevEventGroupV2 OBJECT-GROUP
OBJECTS {
docsDevEvControl,
docsDevEvThrottleAdminStatus,
docsDevEvThrottleThreshold,
docsDevEvThrottleInterval,
docsDevEvReporting,
docsDevEvFirstTime,
docsDevEvLastTime,
docsDevEvCounts,
docsDevEvLevel,
docsDevEvId,
docsDevEvText,
docsDevEvSyslogAddressType,
docsDevEvSyslogAddress,
docsDevEvThrottleThresholdExceeded
}
STATUS current
DESCRIPTION
"A collection of objects used to control and monitor
events. This group replaces docsDevEventGroup.
The event reporting mechanism, and more specifically
docsDevEvReporting, can be used to take advantage of
the event reporting features of RFC3413 and RFC3014."
::= { docsDevGroupsV2 6 }
docsDevFilterLLCGroup OBJECT-GROUP
OBJECTS {
docsDevFilterLLCUnmatchedAction,
docsDevFilterLLCStatus,
docsDevFilterLLCIfIndex,
docsDevFilterLLCProtocolType,
docsDevFilterLLCProtocol,
docsDevFilterLLCMatches
}
STATUS current
DESCRIPTION
"A collection of objects to specify link layer filters."
::= { docsDevGroupsV2 7 }
docsDevInetCpeGroup OBJECT-GROUP
OBJECTS {
docsDevCpeEnroll,
docsDevCpeIpMax,
docsDevCpeInetSource,
docsDevCpeInetRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects used to control the number
and specific values of Internet (e.g., IPv4 and IPv6)
addresses allowed for associated Customer Premises
Equipment (CPE)."
::= { docsDevGroupsV2 8 }
END